Calculate resistance: R = V ÷ I
Find resistance, including decimal currents, and recognize invalid division by zero.
Every step can be opened directly. Reading, exploring and practice do not record a section pass; the untimed assessment does.
Full explanations and worked examples
Useful earlier sections
Understand the electrical relationship
To isolate resistance in V = IR, divide both sides by I: R = V/I. The unit relation is Ω = V/A. A component with 10 V across it and 0.5 A through it has a resistance of 20 Ω because 0.5 × 20 reproduces 10. Use values for the same component.
Dividing by a decimal can increase the numerical answer. Ten divided by one half asks how many halves fit in ten: twenty. For 12/0.3, multiply numerator and denominator by ten to obtain 120/3 = 40. This preserves the ratio; moving the decimal on only one side changes the answer.
Resistance calculated from V and I applies at those operating conditions. An ohmic resistor has approximately constant resistance over the assumed range; a filament can change resistance as it heats. If current is zero, V/I is undefined. Do not invent a finite value by dividing by zero. An ideal open circuit is modeled with unbounded resistance.
Solve and check the problem
Identify voltage and current, convert mA to A, then divide. At 6 V and 3 mA, I = 0.003 A, so R = 6/0.003 = 2,000 Ω = 2 kΩ. Multiplication checks the result: 0.003 × 2,000 = 6. Keep the intermediate ohm value before converting to kilohms.
Estimate whether the result is sensible: relatively little current at a given voltage implies relatively high resistance. If a tiny resistance supposedly permits only tiny current under substantial voltage, reconsider the units. Estimation supports the exact calculation; it does not replace it or justify assumptions absent from the question.
Infer resistance without confusing operating conditions
Resistance is the ratio of voltage across a component to current through that same component at the stated operating point. Both measurement location and unit conversion matter. If a source supplies several parallel branches, source current divided into one branch voltage gives an equivalent network resistance, not automatically that branch’s resistance. Label R_total and R_branch separately. For a series chain, subtract known resistances from the inferred total to recover an unknown component; subtracting voltage directly from resistance would combine incompatible units.
Decimal division can be made exact by multiplying numerator and denominator by the same power of ten. For example, dividing by 0.125 is multiplying by eight because 0.125 = 1/8. When current is in mA, either convert to amperes before finding ohms or use V/mA consistently to obtain kΩ. Check the result with multiplication. A factor-of-1,000 discrepancy is usually a prefix error; changing the answer’s unit label without changing its number does not fix it.
Two operating points can test a constant-resistance assumption. Calculate V/I separately at each point rather than comparing voltages alone. Equal ratios support an ohmic model over those points but do not prove behavior at every temperature or voltage. Unequal ratios show that one constant R cannot represent both sets of exact data; they do not by themselves identify heating, a measurement fault or a particular component type. If I is zero and V is nonzero, V/I has no finite value. If both are zero, there is insufficient information to infer R. Always distinguish an algebraic failure to divide from a physically justified model of an open circuit.
Step-by-step worked examples
Read the question, identify the rule and unknown, then follow each transformation. Check the answer against the original conditions before moving on.
Worked example 1
A resistor has 9 V across it and carries 0.3 A. Find R.
- R = 9/0.3.
- Multiply top and bottom by ten: 90/3.
- R = 30 Ω.
- Check: 0.3 × 30 = 9 V.
Answer: 30 Ω
Worked example 2
Find resistance in kΩ: 15 V at 5 mA.
- 5 mA = 0.005 A.
- R = 15/0.005 = 3,000 Ω.
- 3,000/1,000 = 3 kΩ.
- Check: 0.005 × 3,000 = 15 V.
Answer: 3 kΩ
Worked example 3
A 28.8 V source drives 160 mA through a series pair. One resistor is 73 Ω. Find the other resistor.
- Convert current: 160 mA = 0.16 A.
- Total R = 28.8/0.16 = 180 Ω.
- The other series resistance = 180 − 73 = 107 Ω.
- Check: 0.16 × (73 + 107) = 28.8 V. Using the source voltage for only the unknown resistor would overestimate it.
Answer: 107 Ω
Worked example 4
At one operating point, a component has 13.5 V at 0.3 A. At another, it has 24 V at 0.4 A. Find both resistance ratios and their difference.
- First ratio: R1 = 13.5/0.3 = 45 Ω.
- Second ratio: R2 = 24/0.4 = 60 Ω.
- Difference = 60 − 45 = 15 Ω; a single fixed resistance cannot fit both exact points.
- Do not predict all later behavior from either ratio. These data alone do not establish the physical cause of the change.
Answer: 45 Ω, 60 Ω; increase 15 Ω
Common mistakes and checks
Dividing by 0.5 doubles a value; it does not halve it. Division by zero is undefined.
Check your understanding
- R = V/I uses the same component’s voltage and current.
- Infer total resistance first when solving a network, then isolate the unknown component.
- Zero current cannot be used as a divisor; multiple operating points test the fixed-R assumption.
Concept reference: OpenStax: Ohm’s law and simple circuits. Teaching, examples, and questions here are original educational exercises.
Step 1 of 8 · Understand the task
Read the voltage-to-current ratio
A component’s resistance describes the voltage needed per ampere at its operating conditions. Voltage divided by current gives ohms when current is nonzero.
A larger numerical resistance can result from dividing by a small current. That does not justify reversing the ratio to make division easier.
Make a prediction before learning the rule
Make your best prediction, then use the explanations in the next step to check the reasoning.
Find R from matched V and I
Use the drop across the component and the current through that same component. Normalize mA to A before obtaining ohms; divide an ohm answer by 1000 for kΩ. A zero-current ratio cannot be evaluated by dividing by zero.
Check your understanding
Equivalent resistance differs from individual resistance
Source V divided by total source I gives a whole network’s equivalent resistance. In a series path, subtract known resistors to find another. For two equal parallel branches, each branch carries half the total current, so each resistance is twice the equivalent value.
Check your understanding
Detailed explanation and checks
Useful earlier sections
Understand the electrical relationship
To isolate resistance in V = IR, divide both sides by I: R = V/I. The unit relation is Ω = V/A. A component with 10 V across it and 0.5 A through it has a resistance of 20 Ω because 0.5 × 20 reproduces 10. Use values for the same component.
Dividing by a decimal can increase the numerical answer. Ten divided by one half asks how many halves fit in ten: twenty. For 12/0.3, multiply numerator and denominator by ten to obtain 120/3 = 40. This preserves the ratio; moving the decimal on only one side changes the answer.
Resistance calculated from V and I applies at those operating conditions. An ohmic resistor has approximately constant resistance over the assumed range; a filament can change resistance as it heats. If current is zero, V/I is undefined. Do not invent a finite value by dividing by zero. An ideal open circuit is modeled with unbounded resistance.
Solve and check the problem
Identify voltage and current, convert mA to A, then divide. At 6 V and 3 mA, I = 0.003 A, so R = 6/0.003 = 2,000 Ω = 2 kΩ. Multiplication checks the result: 0.003 × 2,000 = 6. Keep the intermediate ohm value before converting to kilohms.
Estimate whether the result is sensible: relatively little current at a given voltage implies relatively high resistance. If a tiny resistance supposedly permits only tiny current under substantial voltage, reconsider the units. Estimation supports the exact calculation; it does not replace it or justify assumptions absent from the question.
Infer resistance without confusing operating conditions
Resistance is the ratio of voltage across a component to current through that same component at the stated operating point. Both measurement location and unit conversion matter. If a source supplies several parallel branches, source current divided into one branch voltage gives an equivalent network resistance, not automatically that branch’s resistance. Label R_total and R_branch separately. For a series chain, subtract known resistances from the inferred total to recover an unknown component; subtracting voltage directly from resistance would combine incompatible units.
Decimal division can be made exact by multiplying numerator and denominator by the same power of ten. For example, dividing by 0.125 is multiplying by eight because 0.125 = 1/8. When current is in mA, either convert to amperes before finding ohms or use V/mA consistently to obtain kΩ. Check the result with multiplication. A factor-of-1,000 discrepancy is usually a prefix error; changing the answer’s unit label without changing its number does not fix it.
Two operating points can test a constant-resistance assumption. Calculate V/I separately at each point rather than comparing voltages alone. Equal ratios support an ohmic model over those points but do not prove behavior at every temperature or voltage. Unequal ratios show that one constant R cannot represent both sets of exact data; they do not by themselves identify heating, a measurement fault or a particular component type. If I is zero and V is nonzero, V/I has no finite value. If both are zero, there is insufficient information to infer R. Always distinguish an algebraic failure to divide from a physically justified model of an open circuit.
Common mistakes and checks
Dividing by 0.5 doubles a value; it does not halve it. Division by zero is undefined.
- R = V/I uses the same component’s voltage and current.
- Infer total resistance first when solving a network, then isolate the unknown component.
- Zero current cannot be used as a divisor; multiple operating points test the fixed-R assumption.
Follow the worked method
Read worked example 1, then explain its method in the check below. Compare the remaining examples to see where the same method applies and where the conditions change.
Worked example 1
A resistor has 9 V across it and carries 0.3 A. Find R.
- R = 9/0.3.
- Multiply top and bottom by ten: 90/3.
- R = 30 Ω.
- Check: 0.3 × 30 = 9 V.
Answer: 30 Ω
Worked example 2
Find resistance in kΩ: 15 V at 5 mA.
- 5 mA = 0.005 A.
- R = 15/0.005 = 3,000 Ω.
- 3,000/1,000 = 3 kΩ.
- Check: 0.005 × 3,000 = 15 V.
Answer: 3 kΩ
Worked example 3
A 28.8 V source drives 160 mA through a series pair. One resistor is 73 Ω. Find the other resistor.
- Convert current: 160 mA = 0.16 A.
- Total R = 28.8/0.16 = 180 Ω.
- The other series resistance = 180 − 73 = 107 Ω.
- Check: 0.16 × (73 + 107) = 28.8 V. Using the source voltage for only the unknown resistor would overestimate it.
Answer: 107 Ω
Worked example 4
At one operating point, a component has 13.5 V at 0.3 A. At another, it has 24 V at 0.4 A. Find both resistance ratios and their difference.
- First ratio: R1 = 13.5/0.3 = 45 Ω.
- Second ratio: R2 = 24/0.4 = 60 Ω.
- Difference = 60 − 45 = 15 Ω; a single fixed resistance cannot fit both exact points.
- Do not predict all later behavior from either ratio. These data alone do not establish the physical cause of the change.
Answer: 45 Ω, 60 Ω; increase 15 Ω
Explain the worked method
Compare the two conditions
Predict each result from its stated conditions, then compare the explanations. Identify which changed condition makes the difference.
First operating point
An ideal resistor has 4 V across it and 0.2 A through it.
Predict before comparing
Make a prediction and check your reasoning to see the comparison.
Guided practice with less help each time
Work through five exercises. Check each planning step before the final answer; hints become less detailed as you practise.
Guided exercise 1 of 5 · 0 solved
Check one planning step at a time, then give the final answer. Hints stay optional. Viewing a solution does not count as solving the exercise, and guided work does not record a section pass. These practice inputs last in this open page; assessments save separately.
An ideal resistor carries 0.1875 A with 8.8125 V across it. Find R in Ω without reversing the ratio.
R = V/I, with amperes in the denominator.
Planning step 1 of 3
A series path has 13 V and 0.25 A. One resistor is 10 Ω. Find the other resistor in Ω.
Infer total resistance, then subtract the known series resistance.
Planning step 1 of 2
A resistor has 17.8125 V at 312.5 mA. Find resistance in kΩ.
Convert current to A, calculate Ω, then convert to kΩ.
Planning step 1 of 2
Two equal resistors are in parallel across 8.8125 V. Total source current is 0.1875 A. Find each branch resistance in Ω.
Each equal branch carries half the total current.
Planning step 1 of 1
A branch in a 13 V parallel circuit draws 0.25 A. Another branch draws 0.5 A. Find the second branch resistance in Ω.
Use the second branch current with the common voltage.
Planning step 1 of 1
Solve five questions independently
Try each problem without hints. Check after answering and compare the explanation with your own method. These are different questions from the assessment.
Question 1 of 5 · 0 checked
A component has 17.8125 V at 0.3125 A, then 21.5625 V at the same current. Find the increase in its V/I resistance ratio in Ω.
A 12.3125 V source drives series resistors at 0.1875 A. One component drops 3.5 V. Find the resistance of the remaining component in Ω.
A fixed resistor carries 0.25 A at 13 V. To carry 0.375 A with the same resistance, what R in Ω should be used in the calculation?
A source supplies 17.8125 V and 0.9375 A to parallel branches. One branch draws 0.625 A. Find the other branch resistance in Ω.
A series pair has total resistance 141 Ω. At the same current, one resistor drops twice the voltage of the other. Find the smaller resistance in Ω.
Video explanation: Calculate resistance: R = V ÷ I
Optional extra study. Pause to solve the examples on paper, then try this section’s practice questions. Watching does not count as assessment completion.
Ohms Law Explained - The basics circuit theory
The Engineering Mindset · YouTube
Rearrange the relationship to R = V / I and explain which values you need. Compare your result with the direction of change you expect.
Loading video preference…
Players are shown by default unless you have blocked videos in privacy choices. Loading a player connects to Google. Press Play to watch, or close the player above. Videos may include ads or course promotions.