Voltage, current and resistance
Understand what the three quantities mean, use the Ohm’s law triangle, and solve a circuit problem one step at a time.
Every step can be opened directly. Reading, exploring and practice do not record a section pass; the untimed assessment does.
Full explanations and worked examples
Understand the electrical relationship
Voltage V is a potential difference between two points: energy transferred per unit charge. It is measured in volts, also written V. A supply voltage describes the difference available across its terminals. It does not determine current without information about the connected circuit. The V before an equals sign names the quantity; the V after a number names its unit.
Current I is the rate of flow of electric charge, measured in amperes (A). Resistance R describes how strongly a component opposes current, measured in ohms (Ω). A resistor transfers electrical energy into heat; it does not use up current. In one continuous series path, the same steady current enters and leaves each resistor.
For an ideal ohmic resistor at constant temperature and other physical conditions, voltage and current are proportional: V = I × R. This is the model used here. A diode, motor, or changing-temperature filament cannot automatically be treated as one fixed resistor. These lessons are paper calculations, not instructions to work on energized equipment.
Solve and check the problem
Write a given list before calculating: V = 12 V, R = 6 Ω, I = ?. “Across” identifies a voltage between points; “through” identifies current in a component. Read the requested quantity first. Even if two values have the same number, volts and amperes describe different properties and cannot be exchanged.
A closed ideal circuit provides a continuous path. An ideal open circuit does not conduct steady current. A short circuit is not a useful way to obtain more current: actual current is limited by the source and wiring, and the situation can be hazardous. Do not test the model on mains or factory machinery. Use the values supplied in each original exercise.
Read the quantities before calculating
Treat a circuit description as a set of linked measurements. Voltage always belongs to a pair of points; current belongs to a path through a component. Resistance belongs to the component or to a clearly identified equivalent network. Make a three-column given list with the quantity, its value and its unit. A number such as 0.08 is incomplete until you know whether it means amperes, volts or ohms. The same symbol V can name the voltage variable in an equation and the volt unit after a number; its position tells you which meaning is intended.
The physical distinctions explain the algebra. Charge is conserved in steady operation, so the current leaving a resistor equals the current entering it. Energy is transferred in the resistor, so the potential difference across it may be nonzero. Imagine charge as the quantity being transported and voltage as energy transferred per unit of that charge. This helps explain why a resistor can dissipate energy without making downstream charge disappear. It does not imply that current and energy are the same thing, or that the source supplies one fixed current regardless of its load.
Use the equation as a relationship between three quantities for the same resistor. If two are known, isolate the missing one before substituting: multiply I and R for V, divide V by R for I, or divide V by I for R. A consistency check substitutes all three values back into V = IR. If a proposed set fails this check, at least one claim is wrong; the equation alone cannot tell which measurement caused the error. At zero current, do not divide by zero or infer a finite resistance. At zero voltage and zero current, the ratio 0/0 supplies no resistance information.
Step-by-step worked examples
Read the question, identify the rule and unknown, then follow each transformation. Check the answer against the original conditions before moving on.
Worked example 1
A 12 V source is across 6 Ω. Identify the unknown and solve.
- V = 12 V is voltage; R = 6 Ω is resistance.
- Current I is unknown, so use I = V/R.
- I = 12/6 = 2 A.
- Check: 2 × 6 = 12 V.
Answer: 2 A
Worked example 2
A resistor carries 0.5 A with 10 V across it. Find the missing quantity.
- Amperes identify current; volts identify voltage.
- Resistance is missing: R = V/I.
- R = 10/0.5 = 20 Ω.
- Check: 0.5 × 20 = 10 V.
Answer: 20 Ω
Worked example 3
A data card states 7.2 V across a resistor and 0.18 A through it. Identify the missing quantity and find it.
- Volts describe potential difference; amperes describe charge flow. The missing quantity is resistance.
- Rearrange V = IR to R = V/I.
- R = 7.2/0.18 = 720/18 = 40 Ω.
- Check the complete data card: 0.18 × 40 = 7.2 V. Current is not a voltage drop.
Answer: 40 Ω
Worked example 4
A paper model labels one series resistor 27 Ω and 0.4 A, and labels its drop 9.8 V. What drop is consistent with the stated current and resistance?
- The current and resistance refer to this same resistor, so V = IR applies locally.
- V = 0.4 × 27 = 10.8 V.
- The proposed 9.8 V fails the product check; 9.8/27 does not recover 0.4 A.
- Keeping I and R as the stated givens, replace only the calculated voltage with 10.8 V. This does not identify a real instrument fault.
Answer: 10.8 V
Common mistakes and checks
Volts, amperes, and ohms are not interchangeable labels. Current is not consumed by a resistor.
Check your understanding
- Voltage is measured across two points; current flows through a path; resistance links their ratio.
- Use V = IR only with quantities describing the same component or equivalent network.
- A resistor transfers energy; steady current is not used up.
Concept reference: OpenStax: Ohm’s law and simple circuits. Teaching, examples, and questions here are original educational exercises.
Step 1 of 8 · Understand the task
Why does the resistor change the current?
Imagine an inspection fixture represented on paper by a voltage supply, connecting wires and one resistor. The supply has a stated voltage, but that number alone does not tell you the current through the resistor. Choosing a different resistance changes the result even when the supply voltage stays the same.
This lesson explains what voltage, current and resistance mean, then connects them with Ohm’s law. You will predict a change, check it in a simplified model and calculate a missing quantity. The model describes a steady direct-current circuit with one ohmic resistor; it is a learning exercise, not an instruction to assemble or approve equipment.
Make a prediction before learning the rule
Make your best prediction, then use the explanations in the next step to check the reasoning.
Voltage: the electrical difference between two points
Voltage describes a difference in electrical potential between two points. Potential means energy per unit of electric charge. Charge is a property of particles that makes electrical interactions possible; a coulomb (C) is a unit used to measure a quantity of charge. Comparing two points tells us how much energy can be transferred for each coulomb moving between them.
The unit of voltage is the volt, written V. One volt means one joule of energy per coulomb of charge: 1 V = 1 J/C. A joule (J) is a unit of energy. For a 6 V drop across a resistor, each coulomb passing through it transfers 6 J of electrical energy to the resistor. Voltage is therefore an energy-per-charge difference, rather than a count of charges flowing each second.
Say “voltage across the resistor” because you are comparing its two ends. A disconnected source can have voltage between its terminals even though no steady current flows through an external circuit. Current also needs a complete conducting path.
Compare this with water flow
A difference in water pressure between the ends of a pipe is a useful comparison for voltage: it can drive a flow when a path is available.
Where the comparison stops: The pressure comparison helps explain a driving difference. Voltage is measured in volts, not water-pressure units, and the analogy does not describe every electrical device.
Check your understanding
Current: how much charge passes each second
Current is the rate at which electric charge passes a chosen point in a circuit. “Rate” means how much passes in a given time. Imagine marking one position on a wire and counting the amount of charge that crosses it each second. That is different from asking how much energy each coulomb transfers, which is the job of voltage.
The unit of current is the ampere, usually called an amp and written A. One ampere means one coulomb per second: 1 A = 1 C/s. A current of 0.2 A therefore represents 0.2 C passing the marked point each second. The equation symbol for current is I, even though its unit symbol is A. A value such as I = 0.2 A uses both symbols correctly.
In a single steady path, the same current enters and leaves a resistor. The resistor transfers electrical energy to other forms, such as heat; it does not use up the charge. Current is a flow rate, not the speed of one individual electron.
Compare this with water flow
Compare current with the amount of water passing a marked position in a pipe each second. A greater flow rate means more water passes in that time.
Where the comparison stops: Water volume and electric charge have different units. The comparison does not mean that current is used up by a resistor, or that a larger current directly gives an individual electron’s speed.
Check your understanding
Resistance: the link between voltage and current
Resistance describes how strongly a component opposes current for a stated voltage across it. Compare two resistors at the same voltage: the one with higher resistance carries less current. This comparison needs the voltage to stay fixed. Changing both voltage and resistance requires checking both changes.
The unit is the ohm, written Ω. For nonzero current, resistance is found from voltage divided by current: R = V/I. A component with 1 V across it and 1 A through it has 1 Ω at those operating conditions. The unit relationship is 1 Ω = 1 V/A. Resistance is therefore a property inferred from linked voltage and current values, rather than another name for voltage or a quantity of charge.
An ohmic resistor has approximately constant resistance over the conditions being considered, including temperature. Under that assumption, doubling voltage doubles current; doubling resistance at fixed voltage halves current. Some components, including lamps as they heat, do not keep the same resistance. Ohm’s law is useful within its model, but it does not certify equipment safety.
Compare this with water flow
At the same water-pressure difference, a more restrictive pipe section allows a smaller flow. This is a useful comparison for higher resistance giving lower current at fixed voltage.
Where the comparison stops: Pipe geometry is only an analogy. Electrical resistance also depends on material and temperature; the model does not mean a resistor consumes charge or always keeps a constant value.
Check your understanding
The Ohm’s Law Triangle
Ohm’s law relates voltage, current and resistance in an ohmic component under constant physical conditions. Voltage is the electrical potential difference, current is the rate of charge flow, and resistance relates the two.
- V = I × R
- Voltage = Current × Resistance
- I = V ÷ R
- Current = Voltage ÷ Resistance
- R = V ÷ I
- Resistance = Voltage ÷ Current
Cover the quantity you want to find. V sits above I and R: multiply the two lower quantities to find V; divide V by the other lower quantity to find I or R. Division requires a nonzero divisor.
Match the units: use volts (V), amperes (A) and ohms (Ω). Divide mA by 1,000 to get A; multiply kΩ by 1,000 to get Ω. For example, 3 kΩ = 3,000 Ω and 0.004 A = 4 mA.
Find current and keep track of the units
An ideal resistor in a paper inspection-fixture model has 15 V across it and a resistance of 2.5 kΩ. Find the current through it in mA.
Name the unknown and locate the givens
The question asks for current I in milliamperes. The 15 V is across this resistor, and 2.5 kΩ describes this same resistor, so the two givens belong together.
Choose the current relationship
Start with V = I × R. Dividing both sides by the nonzero resistance gives I = V ÷ R. Current is the unknown; multiplying the givens would find the wrong quantity.
Convert resistance before substituting
The prefix kilo means 1,000, so 2.5 kΩ = 2.5 × 1,000 = 2,500 Ω. Using volts and ohms together makes the calculated current come out in amperes.
Calculate, then express the requested unit
I = 15 ÷ 2,500 = 0.006 A. One ampere is 1,000 mA, so 0.006 × 1,000 = 6 mA. The decimal in amperes and the whole number in milliamperes represent the same current.
Check against the original voltage
Multiply the result in amperes by resistance in ohms: 0.006 × 2,500 = 15 V. This recovers the stated voltage. A bare “6” would be incomplete because 6 A and 6 mA are different currents.
Answer: 6 mA (0.006 A)
Explain the result
More worked examples
Use these additional cases to compare quantities, check a formula and inspect the reasoning. The later circuit sections develop series and parallel relationships in detail.
Worked example 1
A 12 V source is across 6 Ω. Identify the unknown and solve.
- V = 12 V is voltage; R = 6 Ω is resistance.
- Current I is unknown, so use I = V/R.
- I = 12/6 = 2 A.
- Check: 2 × 6 = 12 V.
Answer: 2 A
Worked example 2
A resistor carries 0.5 A with 10 V across it. Find the missing quantity.
- Amperes identify current; volts identify voltage.
- Resistance is missing: R = V/I.
- R = 10/0.5 = 20 Ω.
- Check: 0.5 × 20 = 10 V.
Answer: 20 Ω
Worked example 3
A data card states 7.2 V across a resistor and 0.18 A through it. Identify the missing quantity and find it.
- Volts describe potential difference; amperes describe charge flow. The missing quantity is resistance.
- Rearrange V = IR to R = V/I.
- R = 7.2/0.18 = 720/18 = 40 Ω.
- Check the complete data card: 0.18 × 40 = 7.2 V. Current is not a voltage drop.
Answer: 40 Ω
Worked example 4
A paper model labels one series resistor 27 Ω and 0.4 A, and labels its drop 9.8 V. What drop is consistent with the stated current and resistance?
- The current and resistance refer to this same resistor, so V = IR applies locally.
- V = 0.4 × 27 = 10.8 V.
- The proposed 9.8 V fails the product check; 9.8/27 does not recover 0.4 A.
- Keeping I and R as the stated givens, replace only the calculated voltage with 10.8 V. This does not identify a real instrument fault.
Answer: 10.8 V
The Ohm’s Law Triangle
Ohm’s law relates voltage, current and resistance in an ohmic component under constant physical conditions. Voltage is the electrical potential difference, current is the rate of charge flow, and resistance relates the two.
- V = I × R
- Voltage = Current × Resistance
- I = V ÷ R
- Current = Voltage ÷ Resistance
- R = V ÷ I
- Resistance = Voltage ÷ Current
Cover the quantity you want to find. V sits above I and R: multiply the two lower quantities to find V; divide V by the other lower quantity to find I or R. Division requires a nonzero divisor.
Match the units: use volts (V), amperes (A) and ohms (Ω). Divide mA by 1,000 to get A; multiply kΩ by 1,000 to get Ω. For example, 3 kΩ = 3,000 Ω and 0.004 A = 4 mA.
Explore voltage, current and resistance
This closed-circuit model contains one ideal ohmic resistor. Its resistance is treated as constant at each setting. Predict a change, apply it, then compare the values. You can also explore with the sliders.
1 V to 12 V · 1 V steps
100 Ω to 2,000 Ω · 100 Ω steps
Current through the resistor
6 mA ≈ 0.006 A
I = 6 V ÷ 1,000 Ω ≈ 0.006 A
Extra: energy transfer in this model
Power describes the rate of energy transfer. Here P = V × I ≈ 0.036 W (36 mW). Current alone does not tell you whether a real component is within its rating.
This is a simplified calculation model. It does not simulate real component temperature, brightness or protection, and does not approve a real circuit as safe.
Guided practice with less help each time
Work through five exercises. Check each planning step before the final answer; hints become less detailed as you practise.
Guided exercise 1 of 5 · 0 solved
Check one planning step at a time, then give the final answer. Hints stay optional. Viewing a solution does not count as solving the exercise, and guided work does not record a section pass. These practice inputs last in this open page; assessments save separately.
A paper resistor card gives 8 V across an ideal resistor and 2 A through it. What is its resistance in Ω?
Name the unknown, sort the two measurements, then choose the relationship before calculating.
Planning step 1 of 4
In a steady paper circuit model, a 6 Ω ideal resistor carries 0.5 A. Find the voltage across this resistor in V.
Use units to identify the givens and choose the operation. Both values already use A and Ω.
Planning step 1 of 2
A paper test shows 9 V across one 12 Ω ideal resistor. Find the current through that resistor in A.
Select the method, then calculate without separate boxes for the givens.
Planning step 1 of 1
A model has 6 V across a 2 kΩ ideal resistor. Find the current in mA.
This new conversion skill gets extra support: convert resistance, calculate in A, then express the result in mA.
Planning step 1 of 3
In an ohmic model at constant temperature, voltage across a resistor is held fixed while its resistance doubles. What happens to the current?
Predict the relationship without numerical calculation. First state what stays fixed.
Planning step 1 of 1
Solve five questions independently
Try each problem without hints. Check after answering and compare the explanation with your own method. These are different questions from the assessment.
Question 1 of 5 · 0 checked
An inspection note records 0.2 A through a resistor. Which description gives the meaning of that measurement?
A model component has a 15 V drop while carrying 0.3 A. Treat it as an ideal resistor and calculate its resistance in Ω.
A steady current of 0.04 A passes through a 150 Ω ideal resistor on a paper diagram. What voltage in V belongs across its ends?
A paper load is modeled by a 1.2 kΩ ideal resistor with 4.8 V across it. Calculate its current in mA.
A simple steady model contains a source, connecting wires and one resistor in a complete loop. Which statement correctly describes charge passing through the resistor?
Video explanation: Voltage, current & resistance
Optional extra study. Pause to solve the examples on paper, then try this section’s practice questions. Watching does not count as assessment completion.
Ohms Law Explained - The basics circuit theory
The Engineering Mindset · YouTube
Use the circuit explanation to distinguish voltage, current, and resistance. State the unit for each quantity before using a formula.
Loading video preference…
Players are shown by default unless you have blocked videos in privacy choices. Loading a player connects to Google. Press Play to watch, or close the player above. Videos may include ads or course promotions.