Calculate current: I = V ÷ R
Rearrange Ohm’s law for current and verify the answer by multiplication.
Every step can be opened directly. Reading, exploring and practice do not record a section pass; the untimed assessment does.
Full explanations and worked examples
Useful earlier sections
Understand the electrical relationship
Start with V = IR and divide both sides by R to isolate I: current equals voltage divided by resistance. This explains why voltage belongs on top and resistance below. Increasing voltage across the same fixed resistance increases current. Increasing resistance at the same voltage decreases current.
Division may produce a whole number, decimal, or fraction. At 12 V across 8 Ω, current is 12/8 = 1.5 A. At 6 V across 12 Ω, it is 0.5 A. Current below one ampere is entirely reasonable. Never reverse the fraction simply to avoid a decimal.
Use the voltage across the resistor being considered, not every voltage mentioned in a story. A total supply voltage cannot be assigned to each resistor in a series string. First identify the component and its two connection points. Later sections show how the connection changes which values belong in the equation.
Solve and check the problem
Follow given → formula → substitution → answer → check. For 18 V and 6 Ω, I = 18/6 = 3 A. Multiply the result by the same resistance: 3 × 6 = 18 V. This check catches R/V, which also has the wrong units for current. Estimate before calculating to spot a misplaced decimal.
Use multiplication facts and fraction reduction on paper. Reduce 24/16 to 3/2 to obtain 1.5. For 5 V and 2 kΩ, either use 2,000 Ω to obtain 0.0025 A or use V/kΩ consistently to obtain 2.5 mA. These are the same current, expressed in different units. Report the requested unit explicitly.
Choose the correct voltage and resistance
Start from V = IR rather than guessing an order for the numbers. Dividing both sides by the same nonzero resistance gives I = V/R. Its units provide a check: volts divided by ohms are amperes. Reversing the ratio produces conductance units, not current. If the quotient is below one, keep it as a decimal or fraction; changing the order just to obtain a whole number changes the physical question. A fraction such as 7/8 A is as legitimate as 0.875 A.
A question can contain a source voltage, a component voltage and several resistances. Pair values by location before calculating. For a stated resistor drop, use that drop with that resistor. If only a source voltage and a complete series chain are given, add the series resistances before calculating the common path current. If a source voltage and parallel branch resistance are given, the full source voltage belongs to that branch, while source current is the sum of branch currents. The words total, branch and across prevent many errors that arithmetic alone cannot catch.
For changes in a circuit, solve each state with its own givens or compare the ratios. A current difference is I_new − I_old, not a ratio and not a voltage difference. When a known series drop must first be removed from the supply voltage, show that subtraction before division. Check the answer in reverse by multiplying it by the resistance and recovering the exact local voltage used. An estimate also helps: at a fixed positive voltage, increasing resistance must reduce current. These paper models use an ideal source and steady conditions; no procedure for testing equipment follows from a calculated value.
Step-by-step worked examples
Read the question, identify the rule and unknown, then follow each transformation. Check the answer against the original conditions before moving on.
Worked example 1
Find current: 18 V across 12 Ω.
- I = V/R.
- I = 18/12 = 3/2.
- 3/2 = 1.5 A.
- Check: 1.5 × 12 = 18 V.
Answer: 1.5 A
Worked example 2
Find current in mA: 5 V across 2 kΩ.
- 2 kΩ = 2,000 Ω.
- I = 5/2,000 = 0.0025 A.
- Convert: 0.0025 × 1,000 = 2.5 mA.
- Check: 0.0025 × 2,000 = 5 V.
Answer: 2.5 mA
Worked example 3
A 22.5 V ideal source supplies two series components. One drops 6.75 V; the other is 21 Ω. Find the series current.
- Use the sum of series voltage drops: the 21 Ω resistor has 22.5 − 6.75 = 15.75 V.
- Apply the local relationship I = 15.75/21 = 0.75 A.
- The same current flows through the series components.
- Check the second component: 0.75 × 21 = 15.75 V; adding 6.75 V restores 22.5 V.
Answer: 0.75 A
Worked example 4
A branch is 7.5 kΩ across 26.25 V. Another branch draws 2.2 mA. Find total source current in mA.
- For the first branch, V/kΩ gives mA: 26.25/7.5 = 3.5 mA.
- Parallel source current is the sum of branch currents.
- Total = 3.5 + 2.2 = 5.7 mA.
- Do not divide source voltage by 7.5 kΩ and call that total current; it describes only the first branch.
Answer: 5.7 mA
Common mistakes and checks
Do not reverse V/R. Use the voltage across the relevant resistor.
Check your understanding
- I = V/R requires voltage across the resistance being used.
- Use total resistance for total current and branch resistance for branch current.
- Check current by multiplying back to the local voltage.
Concept reference: OpenStax: Ohm’s law and simple circuits. Teaching, examples, and questions here are original educational exercises.
Step 1 of 8 · Understand the task
Use the voltage across the resistor you are calculating
Current is the rate of charge flow through a path. Ohm’s law gives I=V/R for a stated ohmic resistor, but the voltage and resistance must refer to the same component or complete network.
A source voltage is not automatically the drop across every series resistor. Identify the component or path first.
Make a prediction before learning the rule
Make your best prediction, then use the explanations in the next step to check the reasoning.
Isolate current without reversing the ratio
Starting from V=IR, divide both sides by nonzero R to get I=V/R. Volts divided by ohms give amperes. A quotient below 1 is valid; reversing the fraction merely to obtain a larger number changes the physical question.
Check your understanding
Match total and branch quantities
In series, add path resistances before using source voltage, or use one resistor’s own drop with its resistance. Parallel branches share voltage; calculate a missing branch current separately before adding branch currents for the source total.
Check your understanding
Detailed explanation and checks
Useful earlier sections
Understand the electrical relationship
Start with V = IR and divide both sides by R to isolate I: current equals voltage divided by resistance. This explains why voltage belongs on top and resistance below. Increasing voltage across the same fixed resistance increases current. Increasing resistance at the same voltage decreases current.
Division may produce a whole number, decimal, or fraction. At 12 V across 8 Ω, current is 12/8 = 1.5 A. At 6 V across 12 Ω, it is 0.5 A. Current below one ampere is entirely reasonable. Never reverse the fraction simply to avoid a decimal.
Use the voltage across the resistor being considered, not every voltage mentioned in a story. A total supply voltage cannot be assigned to each resistor in a series string. First identify the component and its two connection points. Later sections show how the connection changes which values belong in the equation.
Solve and check the problem
Follow given → formula → substitution → answer → check. For 18 V and 6 Ω, I = 18/6 = 3 A. Multiply the result by the same resistance: 3 × 6 = 18 V. This check catches R/V, which also has the wrong units for current. Estimate before calculating to spot a misplaced decimal.
Use multiplication facts and fraction reduction on paper. Reduce 24/16 to 3/2 to obtain 1.5. For 5 V and 2 kΩ, either use 2,000 Ω to obtain 0.0025 A or use V/kΩ consistently to obtain 2.5 mA. These are the same current, expressed in different units. Report the requested unit explicitly.
Choose the correct voltage and resistance
Start from V = IR rather than guessing an order for the numbers. Dividing both sides by the same nonzero resistance gives I = V/R. Its units provide a check: volts divided by ohms are amperes. Reversing the ratio produces conductance units, not current. If the quotient is below one, keep it as a decimal or fraction; changing the order just to obtain a whole number changes the physical question. A fraction such as 7/8 A is as legitimate as 0.875 A.
A question can contain a source voltage, a component voltage and several resistances. Pair values by location before calculating. For a stated resistor drop, use that drop with that resistor. If only a source voltage and a complete series chain are given, add the series resistances before calculating the common path current. If a source voltage and parallel branch resistance are given, the full source voltage belongs to that branch, while source current is the sum of branch currents. The words total, branch and across prevent many errors that arithmetic alone cannot catch.
For changes in a circuit, solve each state with its own givens or compare the ratios. A current difference is I_new − I_old, not a ratio and not a voltage difference. When a known series drop must first be removed from the supply voltage, show that subtraction before division. Check the answer in reverse by multiplying it by the resistance and recovering the exact local voltage used. An estimate also helps: at a fixed positive voltage, increasing resistance must reduce current. These paper models use an ideal source and steady conditions; no procedure for testing equipment follows from a calculated value.
Common mistakes and checks
Do not reverse V/R. Use the voltage across the relevant resistor.
- I = V/R requires voltage across the resistance being used.
- Use total resistance for total current and branch resistance for branch current.
- Check current by multiplying back to the local voltage.
Follow the worked method
Read worked example 1, then explain its method in the check below. Compare the remaining examples to see where the same method applies and where the conditions change.
Worked example 1
Find current: 18 V across 12 Ω.
- I = V/R.
- I = 18/12 = 3/2.
- 3/2 = 1.5 A.
- Check: 1.5 × 12 = 18 V.
Answer: 1.5 A
Worked example 2
Find current in mA: 5 V across 2 kΩ.
- 2 kΩ = 2,000 Ω.
- I = 5/2,000 = 0.0025 A.
- Convert: 0.0025 × 1,000 = 2.5 mA.
- Check: 0.0025 × 2,000 = 5 V.
Answer: 2.5 mA
Worked example 3
A 22.5 V ideal source supplies two series components. One drops 6.75 V; the other is 21 Ω. Find the series current.
- Use the sum of series voltage drops: the 21 Ω resistor has 22.5 − 6.75 = 15.75 V.
- Apply the local relationship I = 15.75/21 = 0.75 A.
- The same current flows through the series components.
- Check the second component: 0.75 × 21 = 15.75 V; adding 6.75 V restores 22.5 V.
Answer: 0.75 A
Worked example 4
A branch is 7.5 kΩ across 26.25 V. Another branch draws 2.2 mA. Find total source current in mA.
- For the first branch, V/kΩ gives mA: 26.25/7.5 = 3.5 mA.
- Parallel source current is the sum of branch currents.
- Total = 3.5 + 2.2 = 5.7 mA.
- Do not divide source voltage by 7.5 kΩ and call that total current; it describes only the first branch.
Answer: 5.7 mA
Explain the worked method
Compare the two conditions
Predict each result from its stated conditions, then compare the explanations. Identify which changed condition makes the difference.
One resistor
An 18 V source is applied across one 9 Ω ideal resistor.
Predict before comparing
Make a prediction and check your reasoning to see the comparison.
Guided practice with less help each time
Work through five exercises. Check each planning step before the final answer; hints become less detailed as you practise.
Guided exercise 1 of 5 · 0 solved
Check one planning step at a time, then give the final answer. Hints stay optional. Viewing a solution does not count as solving the exercise, and guided work does not record a section pass. These practice inputs last in this open page; assessments save separately.
Find current in A when 14.375 V is across 23 Ω. Show the ratio in the voltage-over-resistance order.
Derive I by dividing V = IR by R.
Planning step 1 of 3
A 23.75 V source feeds a series path. One component drops 4.25 V; the other is 26 Ω. Find path current in A.
Subtract the known drop before using the remaining resistor.
Planning step 1 of 2
A 25.375 V source is across two parallel branches. One has 29 Ω and the other carries 0.375 A. Find total current in A.
Calculate the missing branch current, then add currents.
Planning step 1 of 2
A 28.75 V source drives a series chain of 16 Ω and 30 Ω. Find current in A.
Find the total path resistance before dividing.
Planning step 1 of 1
A 6.5 kΩ resistor has 19.5 V across it. Find current in mA.
Voltage divided by kΩ gives mA.
Planning step 1 of 1
Solve five questions independently
Try each problem without hints. Check after answering and compare the explanation with your own method. These are different questions from the assessment.
Question 1 of 5 · 0 checked
At fixed 29 Ω resistance, voltage changes from 25.375 V to 32.625 V. Find the increase in current in A.
A resistor takes 0.625 A from 14.375 V. At unchanged voltage, its resistance becomes 46 Ω. Find the new current in A.
One branch contains 21 Ω and 5 Ω in series across 19.5 V. Another parallel branch is 78 Ω. Find current in the first complete branch in A.
A junction receives 1.5 A. One outgoing resistor is 29 Ω with 25.375 V across it. Find the other outgoing branch current in A.
A 23 Ω resistor initially has 14.375 V across it. Voltage is reduced by 2.875 V. Find final current in A.
Video explanation: Calculate current: I = V ÷ R
Optional extra study. Pause to solve the examples on paper, then try this section’s practice questions. Watching does not count as assessment completion.
Ohms Law Explained - The basics circuit theory
The Engineering Mindset · YouTube
Identify voltage and resistance, then rearrange the relationship to I = V / R. Check your units and calculate the current on paper.
Loading video preference…
Players are shown by default unless you have blocked videos in privacy choices. Loading a player connects to Google. Press Play to watch, or close the player above. Videos may include ads or course promotions.