Series & parallel resistor circuits
Find equivalent resistance and apply Ohm’s law to total or branch quantities correctly.
Every step can be opened directly. Reading, exploring and practice do not record a section pass; the untimed assessment does.
Full explanations and worked examples
Useful earlier sections
Understand the electrical relationship
Series resistors lie along a single path. They carry the same current, and their resistances add: R_total = R1 + R2 + …. Divide source voltage by total resistance to find the path current. Then use V1 = I × R1 for an individual voltage drop. The drops sum to the source voltage in this ideal DC model.
Parallel branches connect between the same two nodes. Each branch has the same voltage, but its current depends on its own resistance. Branch currents add at the source. Equivalent resistance obeys 1/R_total = 1/R1 + 1/R2 + …. For exactly two resistors, the shortcut R_total = R1R2/(R1 + R2) is valid; it is not a general rule for any number of branches.
With positive resistors, series total resistance exceeds either component; parallel total resistance is smaller than the smallest branch resistance. These bounds catch many mistakes. An open switch in one series path stops ideal current in that path. Opening one parallel branch does not automatically open another intact branch.
Solve and check the problem
Identify the connection before using the numbers. For 4 Ω and 8 Ω in series across 12 V, R_total = 12 Ω and current is 1 A. Drops are 4 V and 8 V. Assigning the full 12 V to both components would incorrectly describe parallel wiring. Label total and component quantities on paper.
For parallel branches of 6 Ω and 3 Ω across 12 V, currents are 2 A and 4 A, totaling 6 A. The equivalent resistance is 12/6 = 2 Ω, below 3 Ω as expected. These are ideal paper scenarios; actual equipment includes source limits and other components and requires approved workplace procedures.
Reduce a network, then restore its branch quantities
Identify nodes before using a series or parallel formula. Components are in series only when the same current must pass through them without splitting at their shared junction. Components are in parallel only when both their endpoints connect to the same pair of nodes. Being drawn side by side is not enough. In a written problem, sketch only the named connections and label the source, each resistor, and any branching points. This prevents treating every resistor as if it had the full source voltage.
Reduce a mixed network from a clearly identified inner group outward. Replace a parallel pair with its equivalent resistance, add any resistance in series with that group, then use the source voltage to find total current. This equivalent resistor reproduces the source’s voltage-current relationship; it does not mean the original branches each carry the total current. Work backward to restore local quantities. Find the drop across a series resistor from total current, subtract that drop from the source to find parallel-group voltage, then divide group voltage by each branch resistance.
Check both kinds of conservation after restoring the circuit. Branch currents must add to the current entering their junction. Voltage drops along any complete source-to-return path must add to source voltage. Positive parallel equivalent resistance must be below the smallest branch resistance, while a series sum must exceed every constituent resistance. For three branches, add all three reciprocals or calculate all three currents; applying the two-resistor product-over-sum shortcut to three raw values is invalid. Opening one branch leaves the remaining branch connected, but if a series resistor precedes the parallel group its drop changes when total current changes. Therefore the surviving branch voltage is not necessarily unchanged. These reductions assume ideal steady DC resistors and an ideal source; arbitrary bridge networks need additional methods beyond this section.
Step-by-step worked examples
Read the question, identify the rule and unknown, then follow each transformation. Check the answer against the original conditions before moving on.
Worked example 1
4 Ω and 8 Ω are in series across 12 V. Find current and each drop.
- R_total = 4 + 8 = 12 Ω.
- I = 12/12 = 1 A through both resistors.
- Drops: 1 × 4 = 4 V; 1 × 8 = 8 V.
- Check: 4 + 8 = 12 V.
Answer: 1 A; drops 4 V and 8 V
Worked example 2
6 Ω and 3 Ω are parallel across 12 V. Find total current and equivalent resistance.
- Each branch has 12 V.
- Branch currents: 12/6 = 2 A and 12/3 = 4 A.
- I_total = 2 + 4 = 6 A.
- R_total = 12/6 = 2 Ω, smaller than either branch.
Answer: 6 A; 2 Ω
Worked example 3
A 42 V source feeds 8 Ω in series with parallel branches of 12 Ω and 24 Ω. Find total current and both branch currents.
- Parallel equivalent = 12 × 24/(12 + 24) = 8 Ω.
- Total R = 8 + 8 = 16 Ω; source I = 42/16 = 2.625 A.
- Series drop = 2.625 × 8 = 21 V, leaving 21 V across the parallel group.
- Branch currents = 21/12 = 1.75 A and 21/24 = 0.875 A.
- Check: 1.75 + 0.875 = 2.625 A, and 21 + 21 = 42 V.
Answer: 2.625 A total; 1.75 A and 0.875 A branches
Worked example 4
Three parallel branches of 15 Ω, 30 Ω and 60 Ω are across 21 V. Find total current and equivalent resistance.
- Every branch has 21 V because it joins the same two source nodes.
- Currents are 21/15 = 1.4 A, 21/30 = 0.7 A, and 21/60 = 0.35 A.
- Total current = 1.4 + 0.7 + 0.35 = 2.45 A.
- Equivalent R = 21/2.45 = 60/7 Ω, approximately 8.5714 Ω.
- Check: 1/15 + 1/30 + 1/60 = 7/60, so the reciprocal is 60/7 Ω; it is below 15 Ω.
Answer: 2.45 A; 60/7 Ω
Worked example 5
One branch contains 7 Ω then 14 Ω in series; another branch is 42 Ω. Both complete branches are across 31.5 V. Find the 14 Ω resistor’s drop.
- The first complete branch has resistance 7 + 14 = 21 Ω.
- Its branch current = 31.5/21 = 1.5 A; it need not equal total source current.
- The 14 Ω resistor’s drop = 1.5 × 14 = 21 V.
- The 7 Ω drop is 10.5 V, and 10.5 + 21 = 31.5 V.
- The other branch current is 31.5/42 = 0.75 A, giving total current 2.25 A; that total must not be used in the 14 Ω resistor.
Answer: 21 V
Worked example 6
A 32 V source feeds 4 Ω in series with two parallel 24 Ω branches. One 24 Ω branch is opened in the paper model. Find the surviving branch current before and after.
- Initially the parallel equivalent is 12 Ω, so total R is 16 Ω and source current is 2 A.
- The series drop is 8 V; each branch has 24 V and carries 1 A.
- After one branch opens, total R = 4 + 24 = 28 Ω.
- The only remaining path carries 32/28 = 8/7 A, about 1.142857 A.
- The surviving branch current rises because the series-resistance drop falls. It is not valid to assume its voltage remains 24 V.
Answer: 1 A before; 8/7 A after
Common mistakes and checks
Series shares current; parallel shares voltage. Do not add parallel resistances as if they were in series.
Check your understanding
- Series shares current; parallel shares voltage between the same two nodes.
- Reduce inward to find total current, then work outward to recover branch quantities.
- Check current sums, voltage sums and equivalent-resistance bounds.
Concept reference: OpenStax: Ohm’s law and simple circuits. Teaching, examples, and questions here are original educational exercises.
Step 1 of 8 · Understand the task
Identify paths before using the numbers
Series resistors occupy one current path, while parallel branches connect between the same two nodes. This connection determines which currents or voltages are shared.
Write total, branch and component next to each quantity. The same resistance values can give very different source currents when their connections change.
Make a prediction before learning the rule
Make your best prediction, then use the explanations in the next step to check the reasoning.
A single series path shares current
Add series resistances to find the whole-path resistance. Source voltage divided by that total gives the common current. Each component drop is its resistance times this current, and the component drops sum to the ideal source voltage.
Check your understanding
Parallel branches share voltage and add current
Find each branch current from its own resistance and the common branch voltage, then add branch currents. Reduce any series resistors within a branch first. For two positive branches, equivalent resistance is below the smaller branch resistance.
Check your understanding
Detailed explanation and checks
Useful earlier sections
Understand the electrical relationship
Series resistors lie along a single path. They carry the same current, and their resistances add: R_total = R1 + R2 + …. Divide source voltage by total resistance to find the path current. Then use V1 = I × R1 for an individual voltage drop. The drops sum to the source voltage in this ideal DC model.
Parallel branches connect between the same two nodes. Each branch has the same voltage, but its current depends on its own resistance. Branch currents add at the source. Equivalent resistance obeys 1/R_total = 1/R1 + 1/R2 + …. For exactly two resistors, the shortcut R_total = R1R2/(R1 + R2) is valid; it is not a general rule for any number of branches.
With positive resistors, series total resistance exceeds either component; parallel total resistance is smaller than the smallest branch resistance. These bounds catch many mistakes. An open switch in one series path stops ideal current in that path. Opening one parallel branch does not automatically open another intact branch.
Solve and check the problem
Identify the connection before using the numbers. For 4 Ω and 8 Ω in series across 12 V, R_total = 12 Ω and current is 1 A. Drops are 4 V and 8 V. Assigning the full 12 V to both components would incorrectly describe parallel wiring. Label total and component quantities on paper.
For parallel branches of 6 Ω and 3 Ω across 12 V, currents are 2 A and 4 A, totaling 6 A. The equivalent resistance is 12/6 = 2 Ω, below 3 Ω as expected. These are ideal paper scenarios; actual equipment includes source limits and other components and requires approved workplace procedures.
Reduce a network, then restore its branch quantities
Identify nodes before using a series or parallel formula. Components are in series only when the same current must pass through them without splitting at their shared junction. Components are in parallel only when both their endpoints connect to the same pair of nodes. Being drawn side by side is not enough. In a written problem, sketch only the named connections and label the source, each resistor, and any branching points. This prevents treating every resistor as if it had the full source voltage.
Reduce a mixed network from a clearly identified inner group outward. Replace a parallel pair with its equivalent resistance, add any resistance in series with that group, then use the source voltage to find total current. This equivalent resistor reproduces the source’s voltage-current relationship; it does not mean the original branches each carry the total current. Work backward to restore local quantities. Find the drop across a series resistor from total current, subtract that drop from the source to find parallel-group voltage, then divide group voltage by each branch resistance.
Check both kinds of conservation after restoring the circuit. Branch currents must add to the current entering their junction. Voltage drops along any complete source-to-return path must add to source voltage. Positive parallel equivalent resistance must be below the smallest branch resistance, while a series sum must exceed every constituent resistance. For three branches, add all three reciprocals or calculate all three currents; applying the two-resistor product-over-sum shortcut to three raw values is invalid. Opening one branch leaves the remaining branch connected, but if a series resistor precedes the parallel group its drop changes when total current changes. Therefore the surviving branch voltage is not necessarily unchanged. These reductions assume ideal steady DC resistors and an ideal source; arbitrary bridge networks need additional methods beyond this section.
Common mistakes and checks
Series shares current; parallel shares voltage. Do not add parallel resistances as if they were in series.
- Series shares current; parallel shares voltage between the same two nodes.
- Reduce inward to find total current, then work outward to recover branch quantities.
- Check current sums, voltage sums and equivalent-resistance bounds.
Follow the worked method
Read worked example 1, then explain its method in the check below. Compare the remaining examples to see where the same method applies and where the conditions change.
Worked example 1
4 Ω and 8 Ω are in series across 12 V. Find current and each drop.
- R_total = 4 + 8 = 12 Ω.
- I = 12/12 = 1 A through both resistors.
- Drops: 1 × 4 = 4 V; 1 × 8 = 8 V.
- Check: 4 + 8 = 12 V.
Answer: 1 A; drops 4 V and 8 V
Worked example 2
6 Ω and 3 Ω are parallel across 12 V. Find total current and equivalent resistance.
- Each branch has 12 V.
- Branch currents: 12/6 = 2 A and 12/3 = 4 A.
- I_total = 2 + 4 = 6 A.
- R_total = 12/6 = 2 Ω, smaller than either branch.
Answer: 6 A; 2 Ω
Worked example 3
A 42 V source feeds 8 Ω in series with parallel branches of 12 Ω and 24 Ω. Find total current and both branch currents.
- Parallel equivalent = 12 × 24/(12 + 24) = 8 Ω.
- Total R = 8 + 8 = 16 Ω; source I = 42/16 = 2.625 A.
- Series drop = 2.625 × 8 = 21 V, leaving 21 V across the parallel group.
- Branch currents = 21/12 = 1.75 A and 21/24 = 0.875 A.
- Check: 1.75 + 0.875 = 2.625 A, and 21 + 21 = 42 V.
Answer: 2.625 A total; 1.75 A and 0.875 A branches
Worked example 4
Three parallel branches of 15 Ω, 30 Ω and 60 Ω are across 21 V. Find total current and equivalent resistance.
- Every branch has 21 V because it joins the same two source nodes.
- Currents are 21/15 = 1.4 A, 21/30 = 0.7 A, and 21/60 = 0.35 A.
- Total current = 1.4 + 0.7 + 0.35 = 2.45 A.
- Equivalent R = 21/2.45 = 60/7 Ω, approximately 8.5714 Ω.
- Check: 1/15 + 1/30 + 1/60 = 7/60, so the reciprocal is 60/7 Ω; it is below 15 Ω.
Answer: 2.45 A; 60/7 Ω
Worked example 5
One branch contains 7 Ω then 14 Ω in series; another branch is 42 Ω. Both complete branches are across 31.5 V. Find the 14 Ω resistor’s drop.
- The first complete branch has resistance 7 + 14 = 21 Ω.
- Its branch current = 31.5/21 = 1.5 A; it need not equal total source current.
- The 14 Ω resistor’s drop = 1.5 × 14 = 21 V.
- The 7 Ω drop is 10.5 V, and 10.5 + 21 = 31.5 V.
- The other branch current is 31.5/42 = 0.75 A, giving total current 2.25 A; that total must not be used in the 14 Ω resistor.
Answer: 21 V
Worked example 6
A 32 V source feeds 4 Ω in series with two parallel 24 Ω branches. One 24 Ω branch is opened in the paper model. Find the surviving branch current before and after.
- Initially the parallel equivalent is 12 Ω, so total R is 16 Ω and source current is 2 A.
- The series drop is 8 V; each branch has 24 V and carries 1 A.
- After one branch opens, total R = 4 + 24 = 28 Ω.
- The only remaining path carries 32/28 = 8/7 A, about 1.142857 A.
- The surviving branch current rises because the series-resistance drop falls. It is not valid to assume its voltage remains 24 V.
Answer: 1 A before; 8/7 A after
Explain the worked method
Compare the two conditions
Predict each result from its stated conditions, then compare the explanations. Identify which changed condition makes the difference.
Series pair
Two 6 Ω resistors are in series across 12 V.
Predict before comparing
Make a prediction and check your reasoning to see the comparison.
Guided practice with less help each time
Work through five exercises. Check each planning step before the final answer; hints become less detailed as you practise.
Guided exercise 1 of 5 · 0 solved
Check one planning step at a time, then give the final answer. Hints stay optional. Viewing a solution does not count as solving the exercise, and guided work does not record a section pass. These practice inputs last in this open page; assessments save separately.
Three series resistors 28 Ω, 32 Ω and 36 Ω carry 0.375 A. Find source voltage in V.
Add the complete path resistance before using V = IR.
Planning step 1 of 3
Parallel branches of 35 Ω and 70 Ω are across 105 V. Find total source current in A.
Find each branch current and add them.
Planning step 1 of 2
A 42 Ω resistor is in series with parallel branches 84 Ω and 84 Ω. Source voltage is 126 V. Find total current in A.
Reduce the parallel pair before adding the series resistor.
Planning step 1 of 2
A 28 Ω resistor precedes parallel branches of 56 Ω and 56 Ω across a 84 V source. Find the voltage across the parallel group in V.
Reduce the group, find total current, then find the group drop.
Planning step 1 of 1
One branch has 35 Ω then 70 Ω in series. It is parallel to a 140 Ω branch across 105 V. Find the 70 Ω resistor's drop in V.
The complete first branch has the source voltage; its individual resistors divide it.
Planning step 1 of 1
Solve five questions independently
Try each problem without hints. Check after answering and compare the explanation with your own method. These are different questions from the assessment.
Question 1 of 5 · 0 checked
Three parallel resistors are 42 Ω, 84 Ω and 168 Ω. Find equivalent resistance in Ω.
A 84 V ideal source feeds 28 Ω in series with parallel 56 Ω and 56 Ω branches. One branch opens. Find the remaining branch current in A after the change.
A 35 Ω resistor feeds parallel resistors 70 Ω and 210 Ω from 175 V. Find current in the 210 Ω branch in A.
Two complete parallel branches are across 105 V. Each branch contains two 42 Ω resistors in series. Find total current in A.
A 84 V source supplies a 28 Ω series resistor and an unknown parallel group. Total current is 1.5 A, and one branch is 84 Ω. Find the other branch's resistance in Ω.
Video explanation: Series & parallel resistor circuits
Optional extra study. Pause to solve the examples on paper, then try this section’s practice questions. Watching does not count as assessment completion.
DC Series circuits explained - The basics working principle
The Engineering Mindset · YouTube
Study the single current path in a series circuit. Compare how total resistance and voltage drops relate to each resistor.
Loading video preference…
DC parallel circuits explained - The basics how parallel circuits work working principle
The Engineering Mindset · YouTube
Compare the branch paths with the series example. Identify which quantity is shared across branches before calculating current or total resistance.
Loading video preference…
Players are shown by default unless you have blocked videos in privacy choices. Loading a player connects to Google. Press Play to watch, or close the player above. Videos may include ads or course promotions.